How to make a book cover out of paper. How to quickly make a phone case

Useful tips

If you urgently need a case for mobile phone To protect it from scratches and falls, you don’t have to go to the store - you can make a beautiful case at home.

How to sew a case with your own hands

1. First, you need to find out what size your future case will be. You can use two halves of felt of different colors. IN in this example dark green was used for the back of the case and white for the front.

2. Both halves are joined manually using thread. A double thread is used (see picture).

3. The back of the case is longer to allow the case to be closed.

4. Sew a small strip of felt at the top of the cover, as shown in the image.

5. To decorate the case, you can prepare several strips of different colors and glue them to the case. If you don't have glue, you can sew them on.

How to sew a phone case with your own hands

You will need:

Scissors

Adhesive tape

Case diagram

Here are a few options and ideas (under the video you will find text instructions):

1. You can create a design for the case yourself by measuring the dimensions of your phone (with a margin). Using an awl, make the holes indicated by the dots.

2. Cut out the sample.

Read also: Tips that will improve the performance of your Android device

3. Hand stitch the thread through the leather swatch.

4. To ensure a strong seam, it is better to sew 3 times.

5. Fasten the left and right sides as shown in the picture and connect them with thread.

6. Apply glue to the bottom of the cover and glue it on the inside.

How to make a case with your own hands.

You will need:

A piece of unwanted leather clothing

Scissors

Sewing machine (you can just use a needle and thread)

1. Prepare a material from which you will later need to cut 3 equal parts - 2 will be used as the front and back of the case, and the third piece for decoration.

2. Place the phone on the material and mark approximately 2.5cm from the top.

3. To decorate the cover, you need to cut the third piece of fabric in half.

4. It's time to cut the fabric into 3 equal parts.

5. Place the two pieces on top of each other and measure approximately 2.5cm from the top.

6. Carefully make a fringe from the halves of the third part.

7. Sew each fringed half to the front and back of the cover as shown in the picture.

8. Cut one piece to the left and right of each fringe.

9. Use a sewing machine to connect the halves of the cover.

Sewing covers with your own hands

Making this case is very simple. This is a quick project if you need a case urgently.

Find out the dimensions of your phone to make it easier in the future.

You will need:

Velcro

Case material

Pins

Two D-rings

1. Prepare the material for the strap. Fold it in half and stitch it as shown in the picture.

2. Prepare 2 pieces of fabric that will serve as the back and front of the cover (in this case, fabric with a pattern). Also prepare 2 pieces of fabric that will make up the inside of the cover (in this case, beige fabric), and 2 pieces of fabric that will cover the beige parts (blue fabric). Place each outer piece on top of the inner piece and connect them with pins.

3. Sew the strap to one of the halves of the case.

4. Place the D-rings on the strap and bend it in the opposite direction. Sew the strap with two rows of threads in the place indicated in the picture.

5. Turn over this part cover and cover with a piece of blue fabric on top.

6. Prepare Velcro, which consists of 2 parts. Sew one part to one half of the cover.

7. Prepare the second half of the cover and sew it to the first.

8. Correctly measure the place where you will sew the second half of the Velcro and sew.

Your case is ready.

DIY leather case

Option 1

1. Prepare an A4 sheet of paper and fold it in half.

2. Mark the outline of your mobile phone on one half of the paper.

3. You will get a figure like this - you need to cut it out.

4. Check if you have chosen the correct size.

5. Now you need to transfer the outline from the sheet to the skin.

You should end up with a segment like this. Fold the ends over and stitch them.

6. Check the size again.

7. Using a ruler and awl, start making holes in the piece.

8. Start sewing. In this case, the color of the thread was chosen in relation to the color of the leather of the case, and the internal seam was used.

9. If after sewing the cover turns out to be uncomfortable, you can turn it inside out, like this.

Option 2

1. Using a plate you can round the bottom of the cover.

2. Run a ribbon along the top of the cover, which should go on both sides.

3. Sew the cover around the perimeter with a double outer seam and then you can decorate it however you like, for example, attach a keychain.

DIY tablet case

The phone case performs not only a decorative, but also a protective function. Today, stores offer a wide range of these products, so there should be no problems with the choice. The only thing that stops many is the price. In this case, there is a great solution - to sew a mobile case yourself. This way you will not only save money, but also get an original accessory.

How to sew a phone case from felt?

Recently, felt has become a fairly popular material. Various jewelry, toys and accessories are made from it. This fabric can also be used to make a cover.

Necessary materials:

Felt of different colors;
Contrasting threads;
Button.

The process of making the accessory is quite simple and even a novice needlewoman can handle it. Cut out two identical rectangles. The basis is the width and length of the phone, plus a few millimeters on each side.

Separately, make a fastening flap, the length of which should be approximately 5-7 cm. Sew the flap to one of the rectangles, stepping back a couple of centimeters from the small side. Now fold the pieces and connect them with a buttonhole stitch over the edge.

Sew a button on the other half to secure the flap. To select the correct distance, place your phone in the case.

How to sew a leather case for a smartphone?

Such accessories are most popular because they are considered universal. In addition, they have a long service life. Such covers are quite expensive, but they are easy to make with your own hands.

Necessary materials:

A piece of leather. An option with an animal print, for example, embossed under python skin, will look original;
Lining material;
Lightning.

It's worth starting with a pattern. To do this, measure your phone and add a few millimeters to the width and length. Taking into account the thickness of the smartphone, make a connection between the rectangles in the center, so that there is some distance to each edge. To make the accessory beautiful, it is recommended to round the edges.

The result should be a solid pattern, which must be transferred to the leather and lining. To prevent the lining fabric from fraying, it is recommended to go along the contour with PVA glue. Now unzip the zipper and attach it using Moment glue or a glue gun to the leather part. Lay everything out carefully.

For fixing, you can use regular clothespins. After a few minutes the glue will dry and they can be removed. Now we sew the leather part attached to the lining. Make sure the zipper is straight. Lay the line at a distance of no more than two millimeters. All that remains is to remove the excess lining fabric and the cover can be used.

We sew a fabric phone case

To make an accessory, you can use completely different materials. It all depends on your imagination. Based on the master class described below, you can make your own original product.

Necessary materials:

Two pieces of matter;
Non-woven fabric;
Keychain ring.

Cut out two rectangles based on the size of the mobile. You can use two different colors. Each part must be reinforced with non-woven material; for this, use an iron. Take a square piece of fabric - we will use it to make a holder for the accessory.

First, make a rectangle out of it, turning the edges inward. Sew it along each edge. Attach a ring to one side by folding and stitching part of the rectangle. Rectangles for the accessory must be processed on one short side; in the future, this part will not be sewn together.

Fold the rectangles inside out, and insert the workpiece between them in the center. Now sew around the perimeter, leaving room to turn the accessory inside out. To sew up the left hole and decorate the product, lay decorative stitches around the perimeter, for example, in the form of snowflakes.

How can you make a cover from a sock?

This option is considered the cheapest because you can use already used socks. This accessory is more suitable for young people, since we will be making it with a cat.

Necessary materials:

High sock with bright print;
White and yellow felt;
Beads.

You should start by measuring your phone. Take a sock and cut off the elastic on it. You need to add 3.5 cm to the length of the phone and cut off the part of the sock corresponding to this value. Now add 1 cm to the width and trim off the excess.

Let's move on to forming the ears. To do this, make a cut in the top center, about 2 cm. Now turn the sock inside out and roll up the ears. To prevent the ears from opening, secure them with a pin. It is important that the lower parts of the triangles are on the same line.

Sew the ears with thread to match the color, just do it so that the thread is not visible on the outside. Turn the sock onto your face and fold it in half – the muzzle should already be visible, let’s move on to its design. To make it, take white felt, draw a circle with a diameter of 4 cm on it and cut it out.

Place it on the sock at a distance of 0.5 cm from the edge where the seam will go, and then sew with matching thread. Using a yellow bead, make a nose.

Place it on the white muzzle a few centimeters from the edge. Using threads of a contrasting color, embroider eyes, antennae and other parts of the face. Now turn the sock inside out, fold it evenly, sew and return it to the right side again.

Let's move on to the lining. To make it, use yellow felt. Cut a rectangle, the length of which should coincide with the cover, and the width should be 2 times larger. Fold it in half and sew the bottom and right sides together, leaving a top hole for the phone.

No need to turn it inside out. Place the lining inside the sock and line up the seams carefully. Make a V-shaped cut and, having made cuts on the triangles, insert the lining into the sock and sew.

How to sew an original case for headphones?

Probably every person has at least once complained that headphones in a bag or pocket get tangled in terrible knots. To prevent this from happening, you can use a special case.

Necessary materials:

Cotton fabric in two colors;
Sintepon;
Lightning;
A piece of felt;
Button;
Lace.

Initially, it is worth mentioning that the process described below can be used as a basis for making accessories of various shapes, for example, a circle, a crescent, etc. This master class will describe a heart-shaped case. As for the color of matter, it all depends on the individual preferences of each person.

To ensure that the main part is even, it is recommended to make a pattern of the desired size. From one half of the fabric (for example, yellow), cut out two hearts, taking into account the seam allowances. Cut one piece in half. Repeat the same with the other half of the fabric (for example, green) and with padding polyester.

If you urgently need a case for your mobile phone to protect it from scratches and falls, then you don’t have to go to the store - you can make a beautiful case at home.

How to sew a case with your own hands

1. First, you need to find out what size your future case will be. You can use two halves of felt of different colors. In this example, we used dark green for the back of the case and white for the front.

2. Both halves are connected manually using thread. A double thread is used (see picture).

3. The back of the case is longer to allow the case to be closed.

4. Sew a small strip of felt at the top of the cover, as shown in the image.

5. To decorate the case, you can prepare several strips of different colors and glue them to the case. If you don't have glue, you can sew them on.

How to sew a phone case with your own hands

You will need:

Scissors

Adhesive tape

Case diagram

1. Print out the diagram of the cover and use an awl to make holes indicated by the dots.

2. Cut out the sample.

3. Hand stitch the thread through the leather swatch.

4. To ensure a strong seam, it is better to stitch 3 times.

5. Fasten the left and right sides as shown in the picture, and connect them with thread.

6. Apply glue to the bottom of the cover and glue it on the inside.

How to make a case with your own hands.

You will need:

A piece of unwanted leather clothing

Scissors

Sewing machine (you can just use a needle and thread)

1. Prepare a material from which you will later need to cut 3 equal parts - 2 will be used as the front and back of the case, and the third piece for decoration.

2. Place the phone on the material and mark approximately 2.5cm from the top part.

3. To decorate the cover, you need to cut the third piece of fabric in half.

4. It's time to cut the fabric into 3 equal parts.

5. Place the two pieces on top of each other and measure approximately 2.5cm from the top.

6. Carefully make a fringe from the halves of the third part.

7. Sew each fringed half to the front and back of the cover as shown in the picture.

8. Cut one piece to the left and right of each fringe.

9. Use a sewing machine to connect the halves of the cover.

Sewing covers with your own hands

Making this case is very simple. This is a quick project if you need a case urgently.

Find out the dimensions of your phone to make it easier in the future.

You will need:

Velcro

Case material

Pins

Two D-rings

1. Prepare material for the strap. Fold it in half and stitch it as shown in the picture.

3. Sew the strap to one of the halves of the case.

4. Place the D-rings on the strap and bend it in the opposite direction. Sew the strap with two rows of threads in the place indicated in the picture.

5. Turn this part of the cover over and cover it with a piece of blue fabric on top.

6. Prepare Velcro, which consists of 2 parts. Sew one part to one half of the cover.

7. Prepare the second half of the cover and sew it to the first.

8. Correctly measure the place where you will sew the second half of the Velcro and sew.

Your case is ready.

DIY leather case

Option 1

1. Prepare an A4 sheet and fold it in half.

2. Mark the outline of your mobile phone on one half of the paper.

3. You will get a figure like this - you need to cut it out.

4. Check if you have chosen the correct size.

5. Now you need to transfer the outline from the sheet to the skin.

You should end up with a segment like this. Fold the ends over and stitch them.

6. Check the size again.

7. Using a ruler and awl, start making holes in the piece.

8. Start sewing. In this case, the color of the thread was chosen in relation to the color of the leather of the case, and the internal seam was used.

9. If after sewing the cover turns out to be uncomfortable, you can turn it inside out, like this.

1. Using a plate, you can round the bottom of the cover.

2. Run a ribbon along the top of the cover, which should go on both sides.

3. Sew the cover around the perimeter with a double outer seam and then you can decorate it however you like, for example, attach a keychain.

The topic of this publication is how to make a leather phone case with your own hands at home. The materials from which modern mobile phones are made are distinguished by their quality and high technology, but still this does not always protect them from various negative influences. Due to an accidental impact or spilled juice, the most unforeseen consequences can occur, rendering the mobile phone unusable. And if a scratched phone simply loses its attractiveness appearance, then one filled with tea may stop working altogether. Usually, phone cases at home are made from soft fabric or leather. Some craftsmen know how to make stylish plastic phone cases from... plastic bottles. True, today such cases do not look very modern. At the end of the article you will find two master classes with which you can easily make DIY leather mobile phone case with a beautiful logo.

To prevent such troubles as scratches or spilled juice, phones began to be “dressed” in cases. Thanks to the case, the phone is more protected both from various physical impacts and from getting wet.

The most highly reliable cases are plastic cases, as they have the best protective characteristics. However, few people choose them, since the phone in such a case does not look very attractive.

You need to put a case on your phone, especially on a woman’s phone, because in your purse, where this is usually located small device, there are also a variety of things that can scratch him. In addition to protecting the phone, the case can also allow you to attach the phone, for example, to the inside pocket of a bag. For this purpose, some cases are equipped with special snap hooks. However, you should be careful with them so that the carabiner itself does not scratch the mobile phone screen. This is especially true for touch phones that are popular today. Therefore, it is so important to choose the right case for your phone - soft, but not thin, capable of protecting the device from damage. You can easily make a case for a touchscreen mobile phone from wool, fabric, soft leather or suede with your own hands. It should be borne in mind that when choosing a model for making a case, it is better to give preference to a simple fabric or leather case rather than one decorated with beads, sequins and rhinestones, which themselves can scratch the phone.

For needlewomen who are keen on sewing, making a cover from scraps is not difficult, especially since they always have plenty of pieces of various fabrics. This is both nice, as it allows you to prepare a gift with your own hands just in case, and useful, because it allows you to use up at least some of the scraps. In addition, you can use leftover braids, ribbons and other materials.

You don't need any special tools to sew a phone case. Everything that is usually used when sewing is used. In addition to tools and materials, you only need a template - a model of the phone for which the case is being sewn. You can use it to take measurements and try on the finished cover. The easiest way to make such a model is from foam plastic.

Master class on making a case with a logo for a mobile phone with your own hands.

How to sew a stylish phone case from soft leather with your own hands. For work

There is no doubt that a mobile case is necessary. Push-button, as well as touchscreen phone, especially the screen, is constantly exposed to mechanical stress: in a bag it rubs against keys, coins and other objects, we place it on various surfaces where there may be not only dirt, but also moisture. With a case, the phone is more protected from harmful influences. There are a lot of necessary devices to protect your mobile phone - panels, cases, silicone pads and bumpers. But all this doesn’t cost a penny. Therefore, you can try to sew a phone case with your own hands from leather, felt, foamiran or any dense fabric. Even minimal sewing skills will do. Sewing a phone case yourself is not such a big problem. The necessary materials and tools can be found in almost any home. It just takes a little effort and a little imagination.

What types of covers can you sew yourself?

The easiest one to make would be a pocket cover. You can simply sew it from two rectangles, or you can complicate the task a little - make a pocket with a tongue made of ribbon, which makes it easier to remove the mobile phone from such a case.
An envelope case with a button will be a little more difficult to make. It is more suitable for women, so it can be sewn from any color material.
A book case is the most practical type, but you will have to work hard to make it, although all the steps are quite understandable.

How to make a homemade case or case for a smartphone? Required Tools

In order to sew a leather phone case with your own hands, you will need the following materials and tools, as well as our master class:

A piece of leather about 3 mm thick or some other material from which you plan to sew the case. The main thing is that it keeps its shape.
An awl and a screwdriver for making straight holes.

Important! These items will definitely come in handy if you work with leather.

Cardboard, ruler, pencil or chalk for cutting out details.
Stationery knife, scissors.
Strong threads to match the material for the case.

Important! You can use a thin strip of leather or decorative cord.

Fasteners, button or magnet, if it is a book case or envelope.
Braid, if it is a pocket cover with a tongue.
Glue gun or Moment glue.
A hammer with an anvil or a special tool for installing eyelets and buttons (if necessary).

Where to begin?

To make a cover or case for your phone with your own hands from leather or other material of your choice, it turns out neat and suitable in all respects:

First, measure the length, width and thickness of your phone.
For the convenience of subsequent construction and fitting, it is advisable to make a mock-up of your mobile phone from cardboard, so as not to have to pull the gadget itself once again. To do this, trace the phone on cardboard and cut it out.
To recreate the desired thickness, cut out several of these templates and stick them on top of each other until you get the desired thickness.
If you have the skills, the right tools and the desire, you can make such a model from plywood.

Case-pocket

If you want to try sewing a leather phone case with your own hands, the patterns are easiest for the pocket case model. It is recommended that a beginner in this field begin his creativity with him.

Sewing such a product will not take much time and does not require special cutting and sewing skills.
To keep it in shape and have a presentable appearance, it is best to make a leather case.
For a girl, you can take skin of any color, be it pink or green, but guys will most likely prefer black or brown.
The material itself must be of good quality and have a thickness of at least 3 mm.

Important! Scraps of leather are sold at the market, in sewing stores, or you can use an old leather bag or cosmetic bag.

Pattern

A simple pocket cover can be tailored in many ways.

Method number 1:

Cut two rectangles of the required size from the leather. To do this, place the mobile template on the flap and trace it with chalk or pencil.
Now make an allowance of 1.5 cm on two long sides of the rectangle and one short one (for the thickness plus the seam).

Important! It’s better to take a little more, if in doubt, than just right. You can always trim off the excess.

There is no seam allowance needed on the fourth narrow side as this edge will not be stitched and it should be level with the edge of the phone.

Method No. 2

If the size of the skin flap allows, then you can cut out one long rectangle, the width of which will be equal to the width of the mobile, plus seam allowances. And the length is equal to twice the length of the phone plus a centimeter for its thickness.

Important! The first option is better to choose when the gadget has smooth shapes and the edges of the case need to be rounded, the second option is when the phone has clear corners.

Assembly

After you have cut out the details of the future case, we begin assembling. This stage requires pedantry.

Important! If each stitch is not clear and identical with the others, the item will have a sloppy appearance.

Sewing halves of a leather product simply with a needle and thread will be problematic. To do this, you must first make holes.

Procedure:

Using a chalk (pencil) and a ruler, draw straight lines where the seam should be. Secure with pins and try to insert the phone. It should fit snugly, but not tightly.
Using an awl, make holes at a distance of 3-5 mm from each other.

Important! If you sew with thread (use nylon or just thick thread), make the distance smaller, and if you use a strip of leather or thin cord (nylon or leather), then make it larger.

Using a screwdriver, process these holes so that they are smooth and without nicks.
If you are joining two rectangles, start stitching from the bottom corner using a blanket stitch. First you connect both halves, and from above you go to only one, just overcast the edge. When you reach the end, connect both parts again until you reach the place where you started the seam.
Finish the top edge of the other half with an overcast stitch separately.
Fasten the ends of the stitch and hide them inside.
If you fold one long rectangle in half, your actions are similar, except that you do not need to overcast the bottom part of the product.

Important! In order for a leather phone case to acquire the desired shape, some experts recommend placing a model that follows the shape of your gadget inside the case and putting the whole thing in cold water for 2 hours. Then take it out and dry it with the “phone” inside. Drying may take 1-2 days.

Using this technology, you can sew a phone case with your own hands from any other dense material that will keep its shape: felt, drape, denim, foamiran, etc.

Pocket case with tongue

How to make a leather phone case so that it is convenient to take it out? This option is not much different in appearance from a simple pocket case, except for one detail - there is a ribbon tab inside, which makes it easier to remove the phone from the case.

Pattern:

Cut a rectangle from a piece of leather, the width of which is equal to the width of the phone plus a centimeter margin on each edge for seams.

Important! The length of this blank should correspond to two lengths of the mobile plus add 1 cm to the thickness of the gadget.

Now we cut out another similar rectangle. Our tongue will be laid between them. That is, one part will be the outside, and the second will be the inside.

Important! If the flap of leather was small and you only had enough for one piece, don’t despair. The inner part - the lining - can be made from any dense but soft fabric that you have on hand, from felt, for example.

We do not touch the first outer side for now, but on the second we mark with chalk or a pencil the places where we will make cuts into which the tongue of the braid will pass.
First, place a strip of approximately 1 cm in the center - it depends on the thickness of the mobile. Next, measure 5 cm from it in one direction and make a longitudinal cut to the width of your braid.
In the second direction, also measure 5 cm and make an incision. Set aside 3 cm upward from it, again make a cut for the braid.
To make the edge of the tongue, which will dangle outside, look presentable, you need to make a leather overlay for it. To do this, cut out 2 small squares from the remaining leather, the side of which will be equal to the width of the braid plus 3 mm for the seam (then you will cut off the excess).
If necessary, you can make additional holes for the charging plug or headphones.

Assembly:

Before sewing the cover, you need to lay out the braid. To do this, burn the edges of the braid with a lighter so that they do not fray.
Then thread it through the lining. Start with the half where there are 2 cuts: first pass the braid in through the first cut, and out through the second.
Then it crosses the center and is again threaded inside the third cut.
Stretch it a couple of centimeters, fix it with a glue gun (leather glue).
Now fold the pattern in half and, leaving a tail of 2 cm outside the cover, trim off the excess.
Place the leather squares that you have prepared on this tail, sew them to the braid, stitching along the perimeter.
Now secure the inner part (lining) to the outer one. This can also be done using a glue gun (you can use Moment glue).

Important! When you glue two parts, first coat the first part halfway with glue, then bend the workpiece in half, and now glue the second part. This will prevent the appearance of wrinkles. In addition, do not apply glue to the part where the braid is located; it needs to move freely.

When you have connected the outer side and the lining, and it is all dry, use an awl and then a screwdriver to make holes along the edge of the cover.
Now, using a thread and a needle or decorative cord and a pin, sew the edges together using a blanket stitch.

Important! Don’t forget to try on the phone case during the sewing process so you don’t have to rip it out later.

Case book

This is a quite practical and convenient case. Sewing a phone case of this type with your own hands is a little more difficult. In addition to leather and a standard set of tools, you will need 2 magnets.

Pattern:

You need to cut a large rectangle from a piece of leather. Its length will be equal to the length of the phone plus a margin of 0.5 cm for the edging, and its width will be twice the width of the gadget plus its thickness.
For a magnetic clasp, you will also need a strip of leather 3-4 cm long and 1.5-2 cm wide (depending on the size of the mobile).
If you want, you can use a second piece of leather or felt to make a lining for the case. This should be a cut of the same size and shape as the outer part. Then, to secure the mobile phone in the case, you will need strips of leather that are attached to the corners.

Assembly:

If you decide to make a case with a lining, then first glue it in with a glue gun.
Sew narrow strips of leather across the corners on the bottom half of the cover, 2 cm from the edge. They will secure your mobile phone in the case by the corners.

Important! The lining should be glued in parts: first one, then bend the cover in half and glue the second one so that there are no wrinkles on the surface.

Now make an awl around the perimeter of the hole, and finish the edges with an overcast stitch.

Important! The thread or cord can be the same color as the skin, or, on the contrary, contrasting.

If you decide to do without a lining, you can secure the phone to the case using double-sided tape. Fix it securely so that it does not fall out.
All that remains is to attach the clasp. To do this, sew it from the inside to the bottom of the cover.
Now glue the magnet to the end of the clasp (1 cm from the edge).
Place the gadget or its three-dimensional model in the case, secure with apothecary rubber bands to secure it.
Now put on the clasp, mark the place for the second magnet and glue it.

All is ready.

Important! From the same pattern you can make a cover with a zipper. To do this, unzip the zipper and secure it around the perimeter with a glue gun, rounding it at the corners. Fasten the zipper and hide its ends inside the case. After this, it’s worth gluing in a lining to make the inside look more aesthetically pleasing.

Envelope case

Making a phone case with your own hands from leather in the form of an envelope is also easy. The only difficulty in this process is making the button clasp. The rest is carried out in almost the same way as in the models described above.

Pattern:

On a piece of leather at least 3 mm thick, draw out the future cover in small pieces. The width is equal to the length of the phone, and the length is equal to triple the width of the mobile (front and back walls of the case and flap), plus take into account the thickness of the gadget and seam allowances.
One side of the narrow part remains flat, and on the other side we cut off the corners so that the case takes the shape of an envelope.

Assembly:

If the length of this workpiece is conditionally divided into three parts, then the first two of them will be rectangular, and the third will be a triangle. Fold the first two parts in half and secure them with paper clips so they don't move.
Make holes with an awl, then sew the sides of the “envelope” with an overcast stitch.
Now use the same stitch to sew the edges of the triangular flap.
All that remains is to install the button. To do this, use a special tool or a hammer and anvil.

Important! If the phone is small, then insert half of the button on the rectangular part of the case before sewing the two halves together, otherwise it will be inconvenient to install it later.

Girls usually prefer to wear an envelope case, so it can be made from bright scraps of leather, and then decorated with something.

Knowing how to sew a leather phone case with your own hands, you can easily turn your idea into reality and make an original case for your gadget. This way, you will protect it from mechanical damage and preserve the beautiful appearance of your smartphone for a long time.