How to remove protective glass from iPhone. Why you can’t change the glass on an iPhone Advantages of replacing the screen with a display module assembly
The protective glass on Apple gadgets is designed to protect the devices from damage. Typically, a high-strength chemical composition is used to protect the display from chips and scratches. Some users neglect such protection, but in vain. Protective glass for iPhone 6 and other gadgets can significantly extend the life of your mobile device.
In this article we will look at how to remove the protective glass from iPhone 5 and devices of other versions. We will also pay attention to how to glue protective glass on an iPhone. In addition, we will try to identify the advantages of this method of protecting the display over conventional film.
How to change and how to glue the glass - read the detailed instructions below.
If we compare the 2 main methods of protecting the iPhone display screen - glass and film - most criteria will be in favor of the first.
The advantages of glass coating are:
- Increased strength with a small thickness of only 0.25 mm.
- The presence of an oleophobic coating that prevents fingerprints from appearing on the display.
- Sometimes - the presence of a nanocoating, which gives increased smoothness to the surface.
- Reliable fastening using silicone elements that prevent the coating from moving and prevent the formation of unevenness and bubbles.
Flexible glass to protect the display of mobile gadgets can also have folded edges. This means that the edges are rounded so the coating is almost invisible. In addition, if the device hits something, the coating will not fall off. So if you are wondering which is the best protective glass, opt for an element with rolled edges.
Removing glass: precautions
Before you get started, there are some rules to consider. First, remember that the glass adheres quite tightly to the display because it is very smooth. But the element is held in place not by glue, but by electrostatic forces. Thus, two perfectly flat surfaces are in close contact, and the glass cannot be removed simply by picking it up with your finger. But you also cannot use a household item, for example, a knife, for this purpose, since there is a risk of damaging the screen or case.
A silicone suction cup will not help in this situation either. If you glue this tool to a damaged coating, a void will form underneath it, and when pressed, it will slide off.
And if the fastening is good, the suction cup will not go anywhere, but another problem will arise. The fact is that the sensor is attached to the body of the gadget using either glue or adhesive tape. The strength of these substances in terms of rupture is much lower than that of glass or touchscreen. Therefore, strong pressure can lead to complete tearing of the display module and damage to its cables. You need to work here carefully and carefully.
How to remove protective glass from iPhone 5S, 4S
Even taking into account the fact that the service life of protective glass is longer than that of films, it also needs to be changed sometimes. The glass comes on a silicone substrate, so it adheres firmly to the display. Removing it will require some skill.
Before removing the protective element, you need to carefully prepare and purchase some tools and materials, namely:
- A spatula (or a thin plastic card), a mediator.
- Silicone suction cup.
- Lint-free cloth.
- A glass cleaner that must contain alcohol.
- Gloves.
Sometimes it happens that all the tools and materials listed above are included with a new protective glass. But this happens quite rarely.
And the glass removal algorithm itself includes the following steps:
1 You need to wash your hands well with soap before starting work, and then dry them. You don't have to do this, but just wear gloves. This is necessary to prevent fingerprints or streaks from appearing on the display. 2 If the glass is damaged, you need to choose the area that is best preserved and has no chips. You need to attach the suction cup to this place, pressing it tightly. 3 You need to place a pick or a spatula in the corner to which the suction cup is attached and pry it off. The edge of the coating should peel off. To do this, you will need to pull the suction cup towards you a little, but not too much. To prevent the screen from falling off. This way we will achieve the goal of creating a small distance between the screen and the glass. But if you don’t have a suction cup, just insert the pick deeper. 4 As you peel off the glass, deepen the tool. And if the display is large, you can use 2 mediators or spatulas for the procedure, moving them in different directions. 5 And the last step is to pull the suction cup towards you so that the glass completely moves away from the screen. In this case, you can grab its edges with your fingers and do the same.
How to stick glass on iPhone 6 and other devices
For everything to go perfectly, you need to glue the glass in a clean room where there is no dust. Before sticking the glass, you need to take a lint-free napkin or a simple cloth and slightly wet the display with a cleaning agent or alcohol. This is necessary to clean the surface and remove fatty elements from it.
The gluing procedure is carried out as follows:
1 Pick up a new protective covering for the display. As with removal, keep your hands clean and dry. Or you need to wear gloves. 2 Remove the protective film covering the sticky surface. To do this, you need to grab it by the tongue and pull. 3 How to glue the element itself? The glass should be kept as close to the iPhone display as possible so that small particles of debris or dust do not get on it. After all, any surface tends to quickly accumulate dust. 4 Place the glass cover a few millimeters from the display, align and center it. When gluing, you need to act carefully and carefully ensure that all the holes for the keys, speaker and other elements match. 5 Next, the protective glass on the iPhone 5 is lowered closer to the screen. Lightly pressing and smoothing movements smooth out the surface. So easily we were able to glue the glass to the display. 6 The surface is wiped with a dry cloth. 7 Remove the glued element on top that protected the glass.If at the end of the procedure you see small dust particles under the protective element, you can peel off part of the glass and blow them out with a vacuum cleaner or remove them with tweezers. Then you need to glue the element back again. You already know how to re-glue glass.
Now you know how to stick a protective glass on an iPhone. There is nothing complicated in this procedure; replacing glass on an iPhone 5S is as easy as shelling pears. Gluing the protective glass on the iPhone requires careful preparation. And the main thing here is to keep everything clean.
Which is better – glass or film?
The answer is obvious - of course, it is better to opt for glass protection. But the point is not only in impact-resistant properties, but also in durability. One has only to note that glass for iPhone 4 or another version of the gadget costs twice as much as regular film.
So the final choice is up to the user. Think for yourself - what is better - to pay more, but in the future avoid expensive device repairs, or save now, but then shell out a lot of money later. Screen replacement is one of the most expensive types of repair for Apple gadgets. But, on the other hand, film cannot be called a bad option either.
As a result, the summary will be as follows. The film is affordable. It protects the display from minor scratches, removes glare and covers the entire screen. Is a protective film for the iPhone screen necessary, given its characteristics? Absolutely yes. Moreover, its cost is low, and how to stick the film is an even simpler task than in the case of glass.
Glass is an expensive option. It gives glare, but transmits light to the maximum, and also reliably protects against strong falls and deep cracks. And if you have found a way to save money on an iPhone, you will not be satisfied with cheap protection options. In any case, knowing how to save up for an expensive device, you can find funds for good accessories for the iPhone 6S or other device.
Glass cracks are a problem that almost every smartphone owner faces. The screen is one of the weak points of iPhones, especially if the phone is not protected by a bumper. A more or less strong blow or fall from a height results in replacement of the display glass, which costs the owner of the gadget a pretty penny.
How to repair iPhone 6 screen
There are two ways to fix the problem: take the equipment to a service center or replace the iPhone 6 glass yourself. The first option is simple and fast: an experienced technician only needs 30-40 minutes to solve the problem. At the same time, he will replace the glass without the display. If you want to save money by repairing your phone yourself, it is better to replace the entire display module.
Benefits of replacing the screen with a display module assembly
To replace the glass of an iPhone separately from the display, you need to have certain skills and additional equipment. Almost anyone can change the display assembly (touchscreen+frame+glass). This option has other advantages:
- The cost of repair is equal to the cost of the module itself. If you order not the original module, but a high-quality copy, you can save even more.
- A completely new display, not just glass.
- No risks associated with falling into the wrong hands (loss of parts, information leakage, etc.).
Instructions for replacing iPhone 6 glass (display module)
Before you replace the glass on your iPhone 6 yourself, prepare a pintalobe screwdriver, a regular Phillips screwdriver, a screen suction cup and a plastic spatula (guitar pick).
When replacing glass on an iPhone 6, know a few rules:
- iPhone screws vary in length. When unscrewing, it is advisable to fold them in order so as not to confuse them later. This is important because If you accidentally screw a long screw into place of a short one, the board may be damaged.
- It is easier to disconnect the cables after a little pre-warming. At home, you can use a hair dryer or hold the device over a light bulb.
- In order not to get confused in the location of parts, it is better to photograph them before disassembling.
Stages of replacing the original glass on an iPhone 6 as part of a module
- Turn off the phone.
- Unscrew the two bottom bolts with a Pintalobe screwdriver.
- Pry off the display with a plastic spatula (pick) and carefully fold it back.
- Use a Phillips screwdriver to unscrew the screws holding the small metal screen.
- Unfasten the 4 cables located under the screen and disconnect the display from the case.
- Unscrew the large metal screen from the old display module.
- Transfer all missing elements from the old module to the new one:
- Home button;
- Speaker;
- Anterior chamber;
- Light and proximity sensors;
- Screw a large metal screen onto the new module.
- Attach 4 trains.
- Screw on a small metal screen.
- Install the two bottom Pintalobe screws.
Turn on the device and check if everything works.
Suitable Products
Found 6 products
-
1200 RUR Buy -
1600 RUR Buy -
1000 RUR Buy
The display is the most fragile and weak point of the iPhone 6. Especially due to its significantly increased dimensions and smoothness, it always tries to slip out of your hands. And then it depends. Experience shows that you are not always lucky, and the frequency of requests for repairs is proof of this.
Depending on the extent of damage, different repair methods are selected. Your iPhone will need to replace its display if it stops responding to commands, or spots, streaks, or smudges appear on the image. In this case, the matrix is probably damaged and cannot be repaired - you will only have to install a new screen.
But if the monitor works, and the glass only cracked (as often happens - they put it in the back pocket of their jeans and sat down), then simply replacing the broken glass with a whole one is enough. Moreover, we do not recommend postponing it for a long time. Sharp edges and fragments inevitably scratch the matrix, it becomes unusable, and then - see above.
In principle, due to the design features, replacing the glass in the iPhone 6 involves installing an entire display unit in the assembly. As a rule, this option is much more expensive due to the high cost of the original spare parts. And another plus is the work of the service department... In order to save at least a little on repairs, we suggest that you try to do it yourself.
We replace the display on iPhone ourselves
In order to change the glass on an iPhone, you will have to partially disassemble its case. Before you start disassembling, do not forget to turn off your smartphone. Find two sockets with star-shaped pentalobe screws near the lightning connector.
Unscrew them with a special pentagonal screwdriver - designed for ø 3.6 mm.
After unscrewing the screws, you need to begin to slowly remove the display cover. To avoid damaging the seal between the glass and the body by prying it with hard objects, it is better to use a regular suction cup with a gripping ring. Place it just above the Home button and pull it lightly.
Just slightly, since the cover, in addition to the screws, is also held in place by a number of latches located around the perimeter. Pull them carefully, starting from the area near the fasteners you just removed and moving further as the case opens.
If you don’t have a suction cup (but we still strongly recommend purchasing one), then you can try using wide tape. It will be much easier to wipe off traces of the adhesive coating of the tape than to restore damaged seals after barbaric rough disassembly. Moreover, after such a procedure you can forget about the vaunted tightness of the case.
Opening the top panel vertically, you will see wire connecting cables located in the camera area. They are the ones that interfere with final removal, so you will have to disconnect them from the system part of the device. However, access to their connectors is blocked by a protective metal strip.
You can get to the connection points between the cables and the board by removing five fastening screws from the protective panel. Don't be alarmed - they have different diameters - that's how it was intended (don't forget this later when assembling).
After unscrewing them, we remove the safety cover.
And now the “sandwich” of trains opens up in front of us in all its glory. We begin, one by one, to disconnect them from the motherboard.
First, the camera cables are removed, then the speakers and the “Home” buttons, and last are the cables for connecting the display.
Try to do everything very carefully so as not to loosen the connectors and reduce the sensitivity of the plugs. In the future, this is fraught with all sorts of interruptions in operation or even serious breakdown.
Done - now the display can be easily disconnected.
Next, you need to remove the earpiece and front camera attached to it from the dismantled non-working top panel, as well as the “Home” button. Since they are not included with the new display part.
We do everything according to the same principle - first remove the metal mounting panels - unscrew the screws, and then disconnect the cables.
This is what the shield above the camera with the speaker looks like.
And so – the connecting cables, carefully disconnect them.
In the photo below - “Home” - the actions are similar: unscrew, remove the shield, disconnect the cable from the board.
Since the “Home” button, for better sealing, has a factory seal, in order to remove it without damage, warm up the case a little. Without special devices, this can be done over a regular light bulb, for example.
And finally, by unscrewing the fastening screws on the arms around the perimeter, we remove the metal plate that protects the display from the inside.
That's it, we successfully completed half of the work. Then, after printing the original new display, reassemble the entire structure in reverse order. Check especially carefully the reliability of all connections of the cables to the board. This is how iPhone glass replacement is usually done. There is nothing complicated.
If you are not sure that you will remember the location of all the disassembled elements and the order in which they are disconnected, then we advise you to photograph all the actions performed step by step. This minimizes the risk of finding “extra” parts after the iPhone glass replacement is completed. To avoid getting confused and losing tiny screws, put them in separate trays.
Is it possible to replace only the glass yourself?
If, after damage, the display matrix continues to work and the image it produces is of good quality, then it will be enough to install new glass. Replacing the iPhone 6 glass will cost much less than reinstalling the entire unit. Even taking into account the work of an experienced professional.
In principle, replacing iPhone glass on your own at home, without a special set of tools and equipment, is hardly possible. Since it is glued very tightly, you cannot simply remove it by hand. You will need a separator to warm up the display, a remover for the factory adhesive coating, new glass, fishing line, special glue and a UV lamp to fix and polymerize it. But they are not cheap, and there is no point in buying everything for a one-time procedure.
The number one question for everyone who has broken their iPhone.
People get angry and offended when they are told: we do not recommend changing the glass on your iPhone. But in vain.
You can change it, there is no problem. Just in the end it will cost you more. Any service will confirm this to you.
Why is that? I decided to turn to trusted professionals and find out what was the matter. What are they afraid of?
What is the difference between “glass” and “module”
Let's immediately understand the terminology.
Glass: a polarizing film and a sensor layer are installed on it on a special film or gel, which recognizes touches. If you break only the glass, then in most cases the image on the screen does not deteriorate, but pixels often begin to burn out and yellow spots and stains appear.
Display: Right - "matrix". On models 3G and 3GS, the matrix is installed separately from the glass and each spare part can be replaced separately without any particular difficulties. On other models it is a tightly glued modular assembly.
Display module: is a single structure made of glass, matrix, sensor part, polarizing film, backlight and mounting frame. Of course, cables are an integral part.
So why does no one allow you to change the glass or are they trying to dissuade you?
1. Glass must be changed under sterile conditions
No, you don't understand. Not just in a more or less clean room without air movement and dust. The conditions must be ideal, simply sterile.
Why? Any speck of dust caught between the glass and the display can ruin the entire procedure. Even if you don’t notice it right away, over time (and temperature changes) a crack from internal pressure may appear in this place. Such defects, by the way, sometimes even occur in factory modules and new iPhones - stories about iPhones whose screens burst “by themselves.”
Of course, most experimental devices are “lucky”: even with dust between the glass and the display, the owners sell or break the iPhone before anything happens. At best, you will walk around with visible dots, noticeable when the backlight is turned on. At worst - well, you get the idea.
2. The procedure takes a lot of time
Broken glass is very difficult to remove from an old module, even if the module itself is not damaged in any way. Small fragments and real glass dust are often almost invisible to the eye. But to install new glass, the surface of the module must be surgically clean.
It turns out that removing the glass itself takes at least an hour of diligent work to remove residues and fragments. And the entire procedure from start to finish can take from two to six hours of work for one specialist.
Compare this with the 20-minute procedure for replacing a module, and the reluctance to deal with glass becomes logical. And we haven't even finished...
3. The equipment is not comparable to the factory one
Machine example (Google Images)
It’s clear that not every service will replace the display manually. Some people buy machines from China for tight and noticeably better glass installation. Looks great, doesn't it?
The problem with all these machines is that they are not perfect. This applies to the procedure, the design, and their calibration. Sometimes (but rarely, which is at least good news) such machines can damage the screen module in the process. This means that the service will still have to install a new one - and lose money on it.
It’s clear that we don’t care about their problems. Or not? Some damage is not immediately noticeable, then you will come back for a warranty on the work... and still get a new module. It's a lose-lose situation, no matter how you slice it.
4. Sizing glass does not guarantee results.
The last and equally sad moment. Sizing is not a panacea. Sometimes after light falls, temperature changes (or strong heating of the device), the glass still begins to peel off from the display. Air “bubbles” appear, which then burst. And again you go to the service.
It is important that the procedure can be done cheaply only if the matrix does not have any damage or visible defects. These could be: yellow stains around the perimeter of the screen, pink spots, dead pixels, translucent vertical stripes and, of course, any cracks. The touchscreen should work perfectly without glitches or broken lines.
In all other cases, you will have to replace the entire display module at a standard price, and maybe even higher than it actually is - taking into account the fact that you already had to spend time coming to the service center and diagnosing it. But it would be easier to pay extra.
Let's be serious: the module is better
I do not claim to be the ultimate truth. To each his own. But I think that module is always preferable to glass. In terms of time, quality of work and even the consequences after replacement.
Maybe absolutely all the masters agree with me? :) For some reason it seems that yes.
You can replace the display module for any iPhone at DamProdam Repair. It only takes 30 minutes, and after that you get a guarantee for the work and a perfectly working device. The cost depends on the device, but there are no supernatural amounts:
- iPhone 5/5s/5c: 6,190 rubles and protective glass/film as a gift.
- iPhone 6: 8,490 rubles
- iPhone 6 Plus: 9,990 rubles
- iPhone 6s: 21,990 rubles
- iPhone 6s Plus: 27,990 rubles
- iPhone 4/4s: 2,500 rubles
The main purpose of a protective glass for a smartphone is to protect the screen from falls, bumps, and scratches. Such glass can serve for a very long time, but over time, chips, cracks, and scratches still appear on it and not only the appearance of the phone deteriorates, but also its functionality - the viewing angle of the smartphone decreases, the sensor may not work correctly. In this case, it is necessary to remove the old glass and stick on a new one, but the removal process is not the easiest task if you do not know all the nuances.
What you need to remove the old protective glass from your phone
It is almost impossible to remove the glass without having anything on hand. And if a regular film can be picked up with a fingernail and peeled off, this will not work with glass. You will need:
- medical gloves – desirable, but not required;
- a flat object, such as a plastic card or guitar pick;
- alcohol-containing glass cleaner or other alcohol-containing substance (vodka, cologne, perfume, etc.);
- lint-free napkin;
- silicone suction cup – preferable.
With this kit, removing the protective glass from your smartphone screen will not be difficult, and the whole process will take 5 minutes. Often, the kit with protective glass already contains all the necessary accessories.
How to remove protective glass from a phone - precautions
The protective glass and the smartphone screen are two perfectly flat surfaces that stick very firmly to each other, and the reason for this is electrostatic forces (with rare exceptions, glue). It is almost impossible to peel them off from each other using a flat object (for example, a knife), but there is a possibility of seriously damaging the smartphone.
It is also unlikely that you will be able to remove the protective glass using only a suction cup, although the chances are greater than in the case of a knife. If the glass is damaged, then most likely the suction cup will simply bounce off without any effect. This is the best case scenario. In the worst case, the sensor will move away from the body, and then you will have to change the entire matrix of the phone, which will be very expensive.
Removing the old protective glass from the phone
- First of all, put gloves on your hands, or if you don’t have them, wash your hands thoroughly with soap and wait until they dry. This will save you from unnecessary streaks on the screen.
- Find the most intact corner of the glass, if it is damaged, away from chips and cracks, and attach a suction cup there.
- Under the glass in the corner where the suction cup is located, insert a card or pick. To do this, pull the suction cup slowly and smoothly, but not sharply, otherwise you may tear off the sensor or screen entirely. If there is no suction cup, then try to carefully make a gap using a card.
- Next, you need to smoothly move the card deeper, peeling off the glass. This needs to be done slowly; if the screen is very large (for example, on a tablet), then it is better to work with two or three cards at the same time.
- When the glass has almost completely come off, pull the suction cup towards you and it will come off.
As you can see, this is not a very complicated procedure, the main thing is to follow the rules.
Gluing new glass to the phone screen
- When the old glass is disposed of, you can begin the process of gluing the new one. This should be done with clean hands in a dust-free room. Wash your hands thoroughly, clean your phone screen with alcohol, and get a new screen protector.
- Remove one film from the side that you want to stick directly to the phone. Keep the glass as close to the surface of the phone as possible. Line it up carefully, making sure all the holes line up, and only then lower the glass completely onto the screen.
- If bubbles appear, they can be easily squeezed out by running a dry cloth over the glass. The last step is to remove the second film and your phone is protected.
It’s quite simple to remove and stick on the protective glass, and for this you don’t have to go to a mobile phone store; you can quickly do everything yourself.
